龙门刨床驱动系统的设计 毕业设计.doc
《龙门刨床驱动系统的设计 毕业设计.doc》由会员分享,可在线阅读,更多相关《龙门刨床驱动系统的设计 毕业设计.doc(51页珍藏版)》请在三一办公上搜索。
1、毕业设计说明书龙门刨床驱动系统的设计班 级: 学号: 软件学院姓 名: 软件工程学 院: 袁文武 祝锡晶专 业: 指导教师: 2014年 6 月龙门刨床驱动系统的设计摘 要文章介绍了以直流电动机为核心的龙门刨床驱动系统的设计,系统采用电流、速度双闭环逻辑无环流可逆直流调速系统,应用反并联可控硅整流装置为系统电机供电,主电路和控制电路的增加了过电流和过电压保护,消除了负载,电网等外界干扰信息最终获得较好的控制效果,对传动中各个环节进行了理论分析,并对动态参数进行了计算,给出了硬件结构和工作情况,实现了刨床的无级调速,大大提高了控制精度和电能利用率,减少了电能损耗和过度时间,降低了控制部件数量,且
2、无噪音,提高了生产效率和质量。该系统的特点是动态响应快、工作可靠、操作简单、精度高。关键词 龙门刨床,直流调速系统,控制电路,逻辑无环流The Design Of Longmen Matchine Drive SystemAbstractThis paper introduces the dc motor as the core of double housing planer drive system design, system adopts the logic without circulation current and speed double closed loop reversi
3、ble dc speed regulating system, applying reverse parallel silicon controlled rectifier device for electric power supply system, the increase of the main circuit and control circuit of over-current and over-voltage protection, eliminating the load, the power grid and other interference information ev
4、entually achieve good control effect, every link in the transmission are analyzed in theory, and the dynamic parameters are calculated, and gives the hardware structure and the working situation, realized the stepless speed regulation of planer, greatly improving the control precision and energy uti
5、lization, reduce the power loss and over time, reduces the number of control unit, and no noise, improves the production efficiency and quality.The characteristics of the system dynamic response is fast, reliable operation, simple operation, high precision.Keyword: double housing planerDc speed cont
6、rol system, Control circuit, Logic without circulation目录1 引言11.1 龙门刨床简介11.2 龙门刨床对电气传动系统的要求11.3 龙门刨床的主要工艺数据12 调速系统各方案的选择32.1 拖动方案的选择32.2 直流调速的方案比较32.3 控制方案的确定42.4 可控硅整流电路的选择42.4.1 单相可控硅整流电路42.4.2 三相半波整流电路52.4.3 三相桥式整流电路53 主回路参数的计算和元件选择83.1 整流变压器的计算83.1.1 整流变压器接线方式83.1.2 整流变压器副级电压的计算83.1.3 整流变压器副级电流计算
7、93.1.4 整流变压器容量计算93.2 可控硅元件的选择93.3 平波电抗器计算124 交流侧和直流侧保护144.1 过电流保护144.1.1 自动开关保护144.1.2 快速熔断器保护144.2 过电压保护144.3 SCR元件过电压保护 165 控制回路设计185.1 电流闭环185.1.1 电流调节器185.1.2 电流闭环工作原理185.2 速度闭环195.3 集成触发电路205.3.1 SCR整流装置对触发器的要求:205.3.2 触发电路的结构及工作原理205.4 无环流逻辑装置235.4.1 无环流系统对逻辑装置的要求:245.4.2 电平检测245.4.3 逻辑判断电路255
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 龙门刨床驱动系统的设计 毕业设计 龙门 刨床 驱动 系统 设计
链接地址:https://www.31ppt.com/p-2947258.html